There are many exquisite antique chairs around the antique or flea market. Its exquisite craftsmanship and shapes are amazing, and why are the chairs for many years still so exquisite, but would you love those dirty or slightly damaged antique chairs? These chairs may not have lost the antique chairs that were exhibited. If you also encounter favorite dirty and dirty antique chairs, you can rejuvenate the damaged antique chair by revamping the touch-up paint yourself and let him increase your presence here. value. Here we will introduce how to refurbish the chair . How does the renovation of the antique chair make up ?
Tools used:
Adhesive Tape, Pen, Paper, Screwdriver, Main Twist, Reversible Clamp, Coloring Wood Putty, Table Saw, Woodworking Tools, Wood Glue, Clamp, Finishing Nails, Hammer, Semi-Paste, Brush, Putty Knife, Steel Wool, Soft Flusive , thinner, fine sand paper, wood dyeing, shellac, 0000 steel wool, colored glass, polyurethane varnish, batting, decorative cloth, paste wax, polishing cloth.
Antique Chair Renovation Steps:
1. The tape tears off the small piece and sticks to the damaged part of the chair. Write a letter or number mark on each piece of tape. Draw a structural sketch for the chair so that you can reassemble it later.
2. Turn the chair and remove the screws. Open and remove the seat cushion. You may need to use soft head or reversible clamps to loosen some debris so that they can be disassembled.
3, repair the damaged parts of the chair. Colored wood putty fills chips or cracks. Remove table saw corners and woodworking tool alternatives to replace broken spindles or stretcher ends. The other party will put new pieces of wood glue and clamp them together.
4. Reinstall your chair based on your chart. Mesida furniture reminds attention to protection and wood glue pieces. A semi-paste finishes the layer of the stripper, using a brushed chair to cover the entire surface. Wait for the chair to blistering, then scrape the putty knife, the oldest finish.
5. Scrub off the remaining, use steel wool dyeing, work to go deep into corners and crevices. Thoroughly wipe a piece of rag and wipe the entire chair to eliminate the remaining stripper and debris. Gently wipe the entire chair with fine sandpaper and wipe the dust with a clean rag.
6. Test the seat frame in the new stain to ensure the original color of the chair. Evenly cover the whole chair stains. After a few minutes, use a clean rag. From the top to the bottom of the stained chair, let it dry for 24 hours.
7. Wipe with a clean rag to remove dust. Describe the entire chair with a thin layer of shellac and wait for it to dry for half an hour.
8, the use of colored glass liquid in the chair with a small brush to see their age. Use a clean rag to absorb the excess glaze. Let the glaze dry, then apply the colored surface of the polyurethane varnish chair.
9, replace the new fabric seat.
10, wooden chair part with 0000 steel wool paste wax. Wait 5 minutes and soak the wax in. Light yellow with a polished cloth.
The above is how to refurbish the introduction of the chair , refurbish their favorite antique old chair, both the sense of achievement and get an elegant and economical antique chair is not beautiful. If you want to learn more about furniture, you can pay attention to GO Home Information Channel.
related articles
How to lacquer wood furniture refurbished wood furniture renovation What are the matters needing attention
Sound Yang furniture - how to do renovation of solid wood furniture
How to refurbish solid wood furniture renovation
Tapered roller bearings are used in a variety of industrial applications. The tapered rollers allow the bearings to accommodate heavy radial, axial and combination loads. This loading flexibility combined with a variety of configurations can be designed from single cups, double cups, and cones. This is why tapered roller bearings are designed into almost every industry, particularly large diameter tapered roller bearings.
Tapered roller bearings are uniquely designed to manage both thrust and radial loads. Consisting of a "tapered cup" and a "tapered cone", this design is one of the most basic and common styles in the bearing industry. Found in everything from cars to conveyor lines, tapered roller bearings are more versatile than any other bearing series. Our taper bearings are sold in sets with both the cup and the cone together.
tapered roller bearings are designed for the most demanding applications in industries such as mining, forestry and steel manufacturing. Utilizing conical rollers and raceways arranged so that the rollers and raceways meet at a common apex, NTN`s tapered Roller Bearing rollers are guided by contact between the large end of the roller, providing high capacity for radial and single thrust loads. With almost 100 million tapered roller bearings manufactured every year under the NTN and Bower brands, it`s no wonder that NTN rivals all major competitors on the market.
We offer premium tapered roller bearings under the NTN and Bower® brand names. Most NTN and all Bower® tapered roller bearings feature case-carburized components. Cups, cones, and rollers are made from case-hardened alloy steel of [Bearing Quality" to provide superior fatigue life and reliability. Precise control of heat treatment, dimensions, and surface finish of the components further contribute to reliable bearing performance. So whether you`re looking for an American-made, case-carburized inch series taper, or a metric series through-hardened variety, we have you covered with a proper fit for your application. Premium steels and heat treatments are also available for applications requiring extended life and high reliability.
Tapered Roller Bearings,Original Taper Roller Bearing,Automotive Bearing Tapered Roller,Agricultural Tapered Roller Bearings
Shijiazhuang Longshu Mechanical & Electrical Equipment Trading Co., Ltd. , https://www.longsbearings.com