China's plastic mold industry and its development needs compared with foreign advanced level, there are six major problems.
(1) Unbalanced development and low overall product level. Although the products of individual companies have reached a fairly high level, some of the products of individual companies have reached or approached the international level, but overall, the accuracy of the molds, rough surface of the cavity Degree, production cycle, life expectancy and other indicators compared with the advanced level in foreign countries still have a big gap. The overall level including production methods and enterprise management, compared with foreign industrial developed countries, there are still more than 10 years gap.
(2) The technological equipment is backward and the organization and coordination ability is poor. Although some of the enterprises have undergone technological transformation in recent years and the technological equipment level is relatively advanced, most of the enterprise's technological equipment is still lagging behind. More importantly, our organization and coordination ability Poor, it is difficult to integrate or mobilize social resources for my own use, and it is difficult to undertake relatively large projects.
(3) Most companies have weak development capabilities. On the one hand, the proportion of technical personnel is low, and the level is not high enough. On the other hand, less investment in scientific research and development, and more importantly, the concept is backward and not enough attention is paid to development.
(4) Management is even more backward than technology. Backwardness is often easy to see, and management is sometimes difficult to realize. However, the gap between the management of mold enterprises at home and abroad is very obvious, and the problems caused by management gaps are often more than technical ones. The gap is even more serious.
(5) With strong market demand, it is still difficult to keep up with the development of production. The contradiction between supply and demand is difficult to solve for a time. The situation of supply exceeding demand will continue for some time, especially in the middle-to-high end products.
(6) It is still a long time to solve the problem of system and talents. In the socialist market economy, in the process of economic globalization, competitive industries, especially those that rely on special users, such as molds, require single-piece production, Many companies' current systems and operating mechanisms are still difficult to adapt to changing markets. The quantity and quality of talents cannot keep pace with the rapid development of the industry. Although all localities are working hard to solve these two problems, they must be resolved better. Wait until the day.
Looking into the future, due to the overall good international and domestic macro environment, the major users of the domestic plastic mold industry will continue to develop at a relatively rapid rate, and plastic molds will also continue to develop at a rapid rate. The major problems that currently exist are through domestic and international exchanges and cooperation. The joint efforts of the entire industry, through common support from all sides, will surely be gradually resolved.
Plastic mold export prospect analysis
China is a developing country. It has the same characteristics as ordinary developing countries, such as low levels of production development, abundant labor resources, low production costs, and broad market prospects. However, China’s per capita GDP has exceeded US$ 2,000, and it also has strong technologies. With the industrial foundation, people are smart, hard-working, dexterous, and a good environment for reform and opening up. These characteristics are very suitable for the development of the mold industry. Therefore, although China's mold industry started relatively late, it has developed rapidly.
From an international point of view, first, as many foreign companies invest in factories in China, more and more, and second, the cost of production of molds in industrialized countries is getting higher and higher, so many industrialized countries in the world are gradually shifting their molds to China. Obviously, due to the rapid improvement of China's mold technology, there is a greater advantage in terms of price and the high cost performance of molds. Therefore, many industrialized countries tend to purchase molds in China. The other aspect is that some developing countries are Weak technical and industrial foundations, and the development of molds can not keep up with economic development at the moment. Therefore, the phenomenon that the supply of molds is in short supply requires more imports. The molds imported from industrial advanced countries are of high quality, but they are expensive, while Chinese molds are Under the premise of satisfying the same requirements, the price is relatively moderate, so there are also many markets. Let us analyze the export market of Chinese molds in recent years. It can be seen that except for Europe, the United States, Japan, and other industrial countries, China is the most export mold country. Outside the major markets, India, Thailand, Malaysia, Vietnam and other countries also have considerable markets. Taiwan’s re-export trade also occupies a considerable market. The China Die and Mould Industry Association organizes and organizes enterprises to visit Europe every year. The United States participates in relevant international exhibitions and plays a very good role in promoting international exchanges and cooperation. 2008 2 In the middle of the month, China Modular Association organized 36 booths for 61 people for the first time to participate in India's international mold and machine tool exhibition, reflecting very enthusiastic, the market is in good condition, especially the plastic mold market is better.