The past two years, the United States and the sewing process slowly into the people's vision, the US seam can be said to be an upgraded version of the seam, the function is much more than the caulk, but the price is relatively higher, some owners may only be business profit One way, I feel that it is absolutely necessary to sew, even without leaving seams. So, do you want to leave seams on the floor tiles ? What are the tips for tiling? The following is just a brief look at it with Xiaobian.
First, do not leave seams on the floor tile
Do not leave seams on the floor tiles, there is a problem of thermal expansion and contraction of the tiles
No matter what brand, what quality of ceramic tile and cement mortar, there will be the problem of heat expansion and shrinkage in the process of temperature and humidity change. If there is no gap of appropriate size when sticking the floor tile, it will be used in the future. It is prone to drumming and cracking.
Sticking the floor tile to leave the seam 2
Now the tiles are all mechanized and the errors will be relatively small. If the error is large, then the quality of the tiles is a problem. However, even if it is a mechanical production, it is inevitable that there will be a little bit of error. If there is no left seam, the situation of uneven seams is likely to occur, which will greatly affect the appearance.
Do not leave seams on the floor tile 3, there is an error in the construction
As we all know, the technical requirements for building floor tiles are very high. Even if you are very experienced, you can't be free from errors in the construction process. Different construction workers will have different results. Therefore, this is one of the reasons that the tiles must be left in the seams. If there are no seams left, it will affect the overall appearance of the home improvement. Therefore, the owner should be as bright as possible during construction, and do not change the construction personnel.
Second, what are the tips for tiling?
1, when the tile laying point
We all know that the tiles must be left in the seams. When will we do the caulking? Generally, we will do jointing and caulking after the tiles and cement mortar are dry. If the cement mortar has not been dried before the jointing, in the future use of the process is likely to appear loose tiles, in general, the time of the jointing at least twenty-four hours after the tile is better .
2, soaking water before tiling
Most bricks need to be soaked in water before they are attached to prevent the tiles from drying too much and absorb the moisture of the cement mortar, causing the tiles to fall off. At present, there is a vitrified tile in the market. Its water absorption rate is relatively low, and it is basically not water-absorbing, so there is no difference in soaking water and it can be pasted directly.
3, how to design the living room floor tiles
The living room is generally the first position to enter the door. When designing a row of bricks, the entrance door must be used as the center line, and the two sides should be arranged in an extended row. The long and wide sides of the general living room are best left and right. It is better to have one whole piece. If there is no way, at least one fifth of the ceramic tile should be guaranteed. Therefore, it is advisable for the owner to purchase a suitable tile after measuring the size of the room, which can reduce a lot of unnecessary losses and make it more beautiful.
4, first floor tile or first shop wall tile
Some homeowners will entangle the first floor tile or the first wall tile when decorating, but in fact, no matter which one is possible, the key is to look at the overall renovation progress, and it is necessary to make progress without delay. Most decoration companies will choose to put a wall tile first, because this will minimize the delay in the construction period.
Editing summary: The above is the small series for you to share on the floor tile to leave seams ? And what are the tips for tiling? We hope to help you. If you want to learn more about decoration, you can follow this site.
Diamond Wire busbar is a kind of ultra-fine and ultra-high strength brass plated steel core wire. It is a core wire material for producing electroplated diamond wire and resin diamond wire, which is produced by using high-quality raw materials, first heat treatment process and wire drawing process. It has high strength and high fine size. excellent surface cleanliness and other characteristics, after being made into diamond wire, it is used in the cutting industry of brittle materials such as solar silicon crystal and sapphire.
Brass Plated Steel Core Wire,Brass Coated Core Wire,Brass Plated Core Wire ,Steel Core Wire
Jiangyin Baoneng Precision New Material Co.,LTD , https://www.baonengwire.com