1. For one week construction site:
Mainly visualize their materials, and examine whether the decoration company's crafts are in line with the scene of the company's work, the decoration of the materials on the construction site, the necessary facilities (such as fire prevention), the completeness of the facilities, and the exchanges between workers and workers, whether there is a temporary consolidation What about a team? A lot of exchanges with workers (remember workers, not foremen) to view the quality of the overall staff, to facilitate the subsequent link, for the environmental protection of materials, should see the decoration company at the scene of the material sampling report, a closer look at the above Marking is consistent with the site material.
2. For the concealed works site at Shi:
From the first section of the complex, and again see the transformation of the circuit embedded, whether it is tidy, whether the interval is fixed according to the specification (normal 50CM), the hardness of the pipe is pinched by hand, whether it is squeezed, whether the PVC joint is fixed and whether the fixed part is Solid, for the wiring box, take a foot on the top to see if it can crush, because the junction box is the hidden place where the owner needs to directly face the switch in the future, its quality is important, for the wooden keel ceiling, a To see if the fire paint brushing is uniform, and second, to see whether the scaffolding of the keel, the spacing of the reinforcement bar spacing, for the waterway renovation, decoration companies most likely to cut corners of the joint is to break the beam, such as Pirza, some people with Pilesa , The above logo, the owner is easy to see, Oh, but forgot to look at the joints, Pilesa joints are more expensive than the pipe N times, and the joints directly affect the quality of water supply, because that is the maximum water pressure The bad joints are prone to problems.
3, for the construction of the site:
In the middle of the general construction, tiles should be tiled, and the base of the wall is also being processed. The panel surface of the wood board has been installed. Basically, the basic living should be out. The highlight here is that the oil mixing practice is super. Whether the splicing carpenter of the length veneer panel has a chamfered seam or not, some people say that it is the problem of the seaming of the oilworker. Even I think that this is a woodworker, and the oiler uses a small knife to cut the depth and opening degree. In the future, it is easy to spit white, long and dumb joints, whether next to use the reinforcement method, pinch about the strength of tile cement sand, whether there is a level ruler around the tiler, whether with a line, the level is in this construction is still Often used? See if there is any wet cement mark on the site. Check the construction drawings on the site. Can it be constructed according to the original drawing? Can it show the effect on the drawing? Does the staffing of the construction site at half of the construction site have the appearance of a pull person? Now the work site Neatness, and stacking with the remaining piecemeal material.
4, on the post site:
A. Check whether it is consistent with the design drawings, the overall perception, first determine whether there is a tacit agreement between the cooperation between the designer and the worker.
B, carpentry look, yin and yang angle work is neat seams neat, the same cabinet decent surface material (pattern is the same), leaving the seams of the practice is the gap neat!
C. Oilworker's point of view, whether the paint is sprayed, whether there is an irregular reflection (can be traced back to the use of the material), whether the base putty (oily, water-based) figure foam is even, and whether there is a leak in the polishing (check the sense of responsibility) The most easily forgotten place is the top of the wooden case. Whether the oilworker polishes and makes up the brush (touch it with his hand to see if there is any burr or smoothness)!
D, bricklayer's point of view: in the construction site to find two kinds of tools, one is a two-meter by the ruler, one is a square, first check the gap is neat, and then use the ruler to see the verticality and flatness of the brick, the smaller the error rate The better, the national standard is 2MM, use a square to check whether the tiling of the yin and yang corners is square, where the corners are touched, and whether the grinding angle of the wall tiles is neat, and whether the emptying rate of the wall and the floor tiles is less than 5%. Putty, is it easy to drop?
E. Finally, take a look at the overall effect of the things you do, and see if there are some places where the two types of jobs are transferred.
Calculation Formula Decoration Company Paint Cement Switch Model Design Decoration Find Decoration Company How Can Decoration Sample Room
Cylindrical Roller Bearings are bearing in which cylinders are used as the rolling elements as opposed to balls in ball bearings. As such, the rollers have a greater (linear) contact area with the outer ring and are distribute loads across a broader surface. Subsequently, they have a relatively high radial load capacity and are suitable for high speeds. Double-row cylindrical roller bearings have high radial rigidity and are used primarily for precision machine tools.
Cylindrical Roller Bearings are designed to carry heavy radial loads. Our cylindrical roller bearings are made with a single row, two rows, or multi-rows of rolling elements to meet an application's radial load requirement. The radial Roller Bearing is available in many standard series and configurations, they are widely used in multiple industries. The combination of high load capacity, moderate speed rating, and industry interchangeability make it one of the most popular bearing designs. These cylindrical roller bearings are produced in ISO series metric, ABMA series metric and inch, journal type, Full Complement series, multi-row series, and cluster mill sizes. These bearings are dimensionally interchangeable to same numbered and sized bearings in the industry. Components of journal bearings and other standard series are made interchangeable with other manufacturer's components. Many mounting arrangements can be achieved with the multiple configurations available with the same load capacity for a given I.D., O.D., and width. Our cylindrical roller bearings can be manufactured in sizes from 3" bore diameter to 84" outside diameter. Internal radial clearances and cage designs can be engineered to your specific application when special applications are encountered.
Cylindrical Roller Bearing,Cylindrical Spherical Roller Bearing,Conveyor Cylindrical Bearing,Cylindrical Roller Ball Bearing
Shijiazhuang Longshu Mechanical & Electrical Equipment Trading Co., Ltd. , https://www.longsbearings.com