1. In the integrated wiring, the frame design is reasonable, and the cable bending radius is ensured. When winding up, down, left, and right around other slots, the slope of the turn must be gentle. Note that whether or not the cables at both ends are sagged can also cover the cover without damaging the cable.
2. During the pay-off process, attention is paid to the control of the pulling force. For cables with reel packaging, it is recommended that at least two workers be arranged at both ends, and the reels should be placed on the qualified pull-rods. The workers at the pay-off end should be first removed from the reel box. Pre-pull a portion of the cable for the collaborator to extract at the other end of the pipeline. The pre-pulled line should not be too much, so as to avoid entanglement on multiple lines.
3. After the cable pulling process is completed, the redundant cables from both ends should be arranged and protected. When the cable is reeled, the original rotation direction should be followed. The coil diameter should not be too small. If possible, use the waste cable end to stipulate on the bridge and ceiling. Or inside the carton, mark it well and remind other people not to step on it.
4. When organizing, lashing, or placing cables, do not use redundant cables. Do not allow the cables to superimpose on the cables. The coils must be consolidated and the fixed cable ties should not be over tightened.
5. During the entire construction period, the process flow was promptly notified and the person in charge of each type of work communicated well. Party A immediately notified Party A of the discovery of the problem and completed the tasks of this type in a timely manner before the start of other follow-up work types.
6. If the unshielded twisted pair cable is installed, the grounding requirement is not high. You can connect the grounding cable to the main slot connected to the cabinet.
7. The specification of the trunking is determined in such a way that the cross-sectional area of ​​the trunking leaves 40% of the surplus to prepare for expansion, and the cross-sectional area of ​​the Category 5 twisted pair is 0.3 square centimeters. When installing the trunking, attention should be paid to isolation from the strong wire trough. The wiring system should be avoided and the strong electric circuit in the wireless shielding, the distance of less than 20cm parallel to walk more than 3 meters. If it cannot be avoided, the section of the trunking must be shielded and insulated. The cable conduits that enter the home are run down the partition walls from the nearest ceiling slot to the ground and are separated from the ground chute pipe to the home.
Pipe transitions, interfaces should not have glitches, slot transitions should be smooth.
Line pipe more than two elbows must stay in the distribution box.
The installation of the wall-mounted bottom box should be more than 30 cm above the ground, and keep equal and parallel with other places.
The line pipe is made of galvanized thin-walled steel pipe or PVC.
Integrated wiring system should be comprehensively considered. Since most of the structured cabling is done by cabling workers, these workers all have professional cabling certifications, so most of the faults can be avoided. However, we still need technology checks when laying the lines. Only when we take note of the above-mentioned common problems can we really achieve “less money, more work, good things, and no bad things†in structured cabling.
2. During the pay-off process, attention is paid to the control of the pulling force. For cables with reel packaging, it is recommended that at least two workers be arranged at both ends, and the reels should be placed on the qualified pull-rods. The workers at the pay-off end should be first removed from the reel box. Pre-pull a portion of the cable for the collaborator to extract at the other end of the pipeline. The pre-pulled line should not be too much, so as to avoid entanglement on multiple lines.
3. After the cable pulling process is completed, the redundant cables from both ends should be arranged and protected. When the cable is reeled, the original rotation direction should be followed. The coil diameter should not be too small. If possible, use the waste cable end to stipulate on the bridge and ceiling. Or inside the carton, mark it well and remind other people not to step on it.
4. When organizing, lashing, or placing cables, do not use redundant cables. Do not allow the cables to superimpose on the cables. The coils must be consolidated and the fixed cable ties should not be over tightened.
5. During the entire construction period, the process flow was promptly notified and the person in charge of each type of work communicated well. Party A immediately notified Party A of the discovery of the problem and completed the tasks of this type in a timely manner before the start of other follow-up work types.
6. If the unshielded twisted pair cable is installed, the grounding requirement is not high. You can connect the grounding cable to the main slot connected to the cabinet.
7. The specification of the trunking is determined in such a way that the cross-sectional area of ​​the trunking leaves 40% of the surplus to prepare for expansion, and the cross-sectional area of ​​the Category 5 twisted pair is 0.3 square centimeters. When installing the trunking, attention should be paid to isolation from the strong wire trough. The wiring system should be avoided and the strong electric circuit in the wireless shielding, the distance of less than 20cm parallel to walk more than 3 meters. If it cannot be avoided, the section of the trunking must be shielded and insulated. The cable conduits that enter the home are run down the partition walls from the nearest ceiling slot to the ground and are separated from the ground chute pipe to the home.
Pipe transitions, interfaces should not have glitches, slot transitions should be smooth.
Line pipe more than two elbows must stay in the distribution box.
The installation of the wall-mounted bottom box should be more than 30 cm above the ground, and keep equal and parallel with other places.
The line pipe is made of galvanized thin-walled steel pipe or PVC.
Integrated wiring system should be comprehensively considered. Since most of the structured cabling is done by cabling workers, these workers all have professional cabling certifications, so most of the faults can be avoided. However, we still need technology checks when laying the lines. Only when we take note of the above-mentioned common problems can we really achieve “less money, more work, good things, and no bad things†in structured cabling.
Suzhou Newstar Hardware Co.,Ltd. is committing to Hand Tool Kits for more than 10 years, now is China good manufacturer and supplier of Hand Tools kits, han tools kit, Hand Tool Set. And we are specialized in Hand Tools Kit Bag, Hand Tool Trolley, Hand Tool Cabinet etc. We are very strong in OEM and ODM services based on customer needs, with customer logo and design.
Hand Tools Kits,Hand Tools Kit,Hand Tools Kit Bag,Hand Tool Kits
SUZHOU NEWSTAR HARDWARE CO.,LTD. , https://www.sjnewstarhardware.com