Today Xiaobian brings you the relevant content to teach you to install hot and cold water faucets . It must be said that with the development of the times, people's living standards are getting higher and higher. The decoration of the kitchen is often taken seriously. Compared with the traditional faucet hot and cold water taps, it is more convenient to use, and has been favored by users. If you don't know how to install it, let Xiaobian teach you to install the hot and cold water tap. The following small series will quickly introduce you to teach you to install hot and cold water taps:
First, teach you to install hot and cold water faucet
1, kitchen sink hot and cold water faucet installation method:
In the winter, washing dishes in the kitchen is very sinful. If you install a hot and cold water faucet in the kitchen, you can prevent cold washing in winter. In the kitchen, only the sink and the sink need to be equipped with hot and cold water faucets. This type of hot and cold water faucet is relatively simple to install. Generally, there are two hoses, copper buckles, rubber pads, faucets and other accessories. The copper buckles and rubber pads are placed. Into the hose, then the hose is connected to the opening of the sink, then the rubber mat is transferred into the hose, the copper wire is transferred into the hose, and then the faucet is placed on the copper tube. At the same time, the copper wire should also be fixed firmly. Finally, put it into the hole interface of the sink, then tighten it, and then connect the same hose to the water outlet. It is best to mark the cold water pipe, otherwise it will be wrong to use.
2, bathroom shower hot and cold water faucet installation method:
Hot and cold faucets are also a must-have installation in the bathroom. When installing, you need to express the hot and cold water pipes separately. Generally, the red color on the left side is connected to the hot water, and the blue color on the right side is connected to the cold water. The interface needs to be wrapped with waterproof tape to prevent leakage, and then the faucet is connected to the interface. The wrench is tightened. Then turn on the faucet and test it according to the cold first, then there is no running water. The hook of the bathroom shower is generally installed and adjusted according to the height of the user. The hand-type vertical hand shower is a common type of shower, the installation height is generally 2050mm-2200mm, and the height of the ceiling shower is generally 2100mm-2300mm, it is necessary to consider the height of the user when installing.
3, the installation of thermostat
Before installing the thermostatic faucet, first check which side of the water pipe is cold water, which side is hot water, and connect the hot and cold water pipes to avoid affecting the future work of the faucet. Gas and solar water heaters cannot use thermostatic faucets, mainly because the water pressure is too low. Install the thermostatic faucet and install a hot and cold water filter.
Second, the precautions for installing hot and cold water faucets
1. Do not install the hot and cold water supply pipes. Generally, the hot water pipes are on the left side and the cold water pipes are on the right side.
2, can minimize the distance between the hot water supply and the faucet, so that the hot water can be delivered to the faucet in a short time;
3. According to the instructions of the faucet manual, do not miss or damage the gasket and other small accessories;
4. If there is too much water pressure difference between hot and cold water, use a tool knife to adjust the valve of the bracket.
Well, the above is about the introduction of the relevant content to teach you to install hot and cold water taps. After reading this article, I believe that you have a certain understanding of teaching you to install hot and cold water taps. When you install hot and cold water faucets, please refer to the comments of Xiaobian! If you want to know more about decoration, please continue to pay attention to the decoration home network.
Function introduction
★ According to the serial port or industrial Ethernet interface data, read the corresponding text, picture, video, and display the corresponding content.
★ Modify the display text, picture, video function through the serial port or industrial Ethernet interface.
★ Set parameters.
★ The function of setting the display parameters through the serial port or industrial Ethernet interface; including: grayscale,color, brightness, display speed, screen split and merge, etc.
We providing Transparent Led Glass Display,Transparent LED Display Led Screen,Transparent Led Glass Display Outdoor,Transparent Led Glass Display Indoor.
Transparent Led Glass Display,Transparent LED Display Led Screen,Transparent Led Glass Display Outdoor,Transparent Led Glass Display Indoor
Shenzhen Filmbase Technology Co., Ltd. , https://www.globalfilmbase.com