Bathroom ware can be said to be used by every family, and there are many types of bathroom ware. Its arrangement is also very particular. However, choosing a good bathroom ware will make your life comfortable and comfortable. Then, Xiaobian will introduce bathroom ware installation methods and bathroom ware purchase techniques.
Installation of bathtub installation method for bathroom ware
1, test the water is leaking: Put the bathtub before the first water accessories, do 24 hours closed water, see if the bathtub leaks, pay special attention to the overflow.
2, the leveling of the bathtub: When placing the bathtub, pay attention to the other end of the outlet slightly higher than the end of the drain, so that the future sewage is not smooth. The bathtub maintains a visually beautiful appearance without affecting the drainage effect.
3, sand filling: Although the cast iron bathtub is strong, but its thermal conductivity is very fast, it should be used in the river sand, in the bottom of the bathtub firm, compact. It is also recommended that foam be used, considering that the foam is not as mobile as river sand and it is very suitable for filling all the gaps. In the process of filling sand, how to make sand not leak into the sewage pipe is a problem to be solved.
4. Leave the access hole: Leave 300mm wide and 400mm hole in the water outlet, cut a mouth piece according to the size, cut the planks (thickness 40mm) made of waterproof and anti-corrosion treatment according to the size, and calculate the bricks on the plate. Numbers and Alignment Plaster bricks on wooden boards with 903 construction adhesive. The sealant was applied to the edge of the tile and was inserted into the box to facilitate overhauling of the bathtub's drainage system in the future.
Toilet bowl installation method washbasin installation
1. Install the washbasin: Install a washstand with a pipe rack. Draw a vertical line in the middle of the drain nozzle. Measure the vertical height upward from the floor and draw a horizontal line on the wall. Draw a mark on the wall according to the width of the washbasin. , Hit holes 120 mm in diameter. Drain the bricks and other debris from the hole, insert the expansion bolts into the hole, and pry with the cement. The fine tubing should be hung upright. Put the bolts on the rubber pads and eye sockets, and put on the nuts, and screw them to the appropriate pipe end. Head over the basin fixing hole. Place the washbasin on the rack to find a flat surface. Attach a 4 mm diameter bolt to a horizontal iron bar, insert the upper end into the mounting hole, and insert the lower end into the tube rack. Put on the nut and tighten until tight.
2. To install a cast iron basin, draw a vertical line at the center of the nozzle. Measure the vertical height upwards from the ground. Draw a horizontal line as a crosshair. Press the width of the basin to draw a mark on the horizontal line. Each vertical line was drawn and the pots were set up. The screw holes were placed in holes of 15 mm in diameter and 70 mm in length. The lead rolled into a roll and cut into a hole. Use the screws to fasten the frame to the wall. Place the washbasin on the rack, pull the bolt of the movable frame open, pull out the movable frame, and hook the frame to the washbasin hole. Inside, tighten the movable frame screws again, leveling and aligning.
Toilet toilet installation method toilet installation
1. Take out the pipe plug of the ground water outlet. After checking that there is no debris in the pipe, clean the area around the nozzle. Align the outlet pipe of the toilet with the nozzle of the water pipe. Make sure that the pipe is flush and correct. Draw a mark on the hole of the toilet bolt. , Remove the toilet.
2. Drill a hole with a diameter of 20 mm and a depth of 60 mm at the imprint, insert a 10 mm diameter bolt into the hole, secure it with cement, align the eyes of the toilet with the bolt, align it with the mark, and place the seat after the test. The toilet was removed. Put putty around the outlet of the toilet bowl and the nozzle of the water pipe, and then align the four bolt holes of the toilet with the bolt, lay it flat and align it. Put a rubber pad on the bolt, screw on the nut, and tighten to a moderate degree.
3. Align the rear center of the toilet and draw a vertical line. Draw a horizontal line at a height of 800 mm from the ground. Draw a seal on the horizontal line according to the positions of the two side holes on the back of the tank. Play a diameter of 30 mm and a depth of 70 at the hole. Millimeter hole. Insert a bolt 10 mm in diameter and 100 mm in length into the hole and secure it with cement. Hang the back tank on the bolts, align and align, especially align with the center of the toilet. Put a good rubber pad on the bolt, screw on the nut, and tighten it to a moderate degree.
4. When installing the backwater tank water elbow, first remove the nuts of the backwater tank outlet and the toilet water inlet, and put it back to back on the water elbow. The rubber pad is also placed on the sewage pipe. Insert the upper end of the water elbow into the drain of the back tank, insert the lower end into the water inlet of the toilet, push the pad to the outlet, screw on the nut, straighten the water elbow and straighten it, and tighten it with the pliers. Moderate.
5. When using the eight-character door to connect the Sheung Shui, it is necessary to first measure the size of the water tank's slopping door from the upper water outlet, complete the short section, install the eight-character door, and put it into the mouth of the upper water pipe. If the copper tube or plastic tube is cut off, it is necessary to use the mother's lamp fork to bend the mother. Then the nuts and nuts are placed back-to-back on the copper tube or the plastic tube. The tubes are wrapped with oil asbestos rope or lead-oil twine, respectively. Insert the drift door and eight-word door entrance and exit, tighten the nut.
Bathroom ware purchase skills
1, the amount: measure the size of the bathroom area and decorative style.
2ã€Thinking: When purchasing, you should first think of ancillary products. All parts and accessories of the whole set of products should all be at the same grade level. The matching product style and color must match the style of bathroom decoration so as to be harmonious and beautiful.
3, choose: choose the right size bathroom products, determine the toilet drainage method, installation size and other bathroom products and bathroom size, style is consistent.
4, to see: You can choose under strong light, carefully observe the reflective surface of the bathroom products from the side, the surface has no or little trachoma and pitting is better; high brightness index products using high-quality glazed materials and very A good glazing process has good reflectivity to light and thus has a good visual effect.
5, touch: You can use your hands to gently rub on the surface, I feel very smooth and delicate as well; you can touch the back, I feel there is a "fried" fine feeling of friction as well.
6. Listening: The surface of the ceramic can be tapped by hand. Generally, a sound made by a good ceramic material is relatively crisp. When there is husky sound, there may be cracks.
7, than: mainly in the study of water absorption, the lower the water absorption the better. Ceramic products have a certain adsorption and infiltration capacity for water. If water is absorbed into the ceramic, it will have a certain degree of expansion, which will easily cause the glaze on the ceramic surface to crack due to expansion; especially for toilets, if the water absorption rate is high, it is easy. Inhalation of dirt and odors in water can cause unremovable odors over time.
8, recognize: recognize the brand, recognize service, recognize water. Yangzi Sanitary and Sanitary has passed the water-saving certification, but also has national brand-name products, consumers can rest assured to purchase. At the same time, there are certain requirements for the installation of toilets, which must be installed by professional installers.
9, buy: After the above layers of test, the final comparison of three, rest assured to buy.
Editor's summary: The sanitary ware installation method and sanitary ware purchase techniques are introduced here, and we hope to help everyone. If you want to know more related information, you can pay attention to this website information.
Sanitary ware maintenance sanitary ware
Industrial Automatic High Performance Doors
High performance doors have unique advantages compared with other types of doors. Very fast running speed, High frequency working, Intelligent automatic control, High safety level, and high profile appearance. With such high performance doors, it will bring big benefits in many aspects, like higher work efficiency, high automation level, and keep better clean and temperature.
high performance door, high performance industrial doors, commercial high performance doors
SHANGHAI KENVO DOOR CO.,LTD , https://www.kenvodoor.com