[Asia Pump Network hearing] pump installation is reasonable, the normal operation of the pump and the life has a very important impact, so the installation and calibration must be carefully carried out. Now to introduce IHF-lined fluorine plastic centrifugal pump installation, operation precautions and maintenance methods. IHF-lined fluorine plastic centrifugal pump I. IHF-lined fluorine plastic centrifugal pump installation considerations 1, control the installation of the size of the embedded good foundation bolts, do a good job of concrete foundation. 2, to be based on the foundation cement solidification, the pump installed on the basis of the level of the pump and motor shaft level check, if not level, the use of horns until the level of leveling, tighten the bottom nut after tightening. 3, check the rotating parts of the pump is stuck rub phenomenon should be strictly check the coaxiality of the pump shaft and the motor can be adjusted to make it concentric sheet, the last hand to rotate the coupling, the phenomenon of easy and uniform rotation without rubbing Normal. 4, pump suction and discharge pipe should have their own bracket, does not allow the weight of the pipe directly to withstand the pump, so as to avoid the pump crushed. 5, the installation of the pump above the liquid level (within the pump suction allowable range), the end of the suction pipe should be installed on the end of the valve, and in the discharge pipe set up irrigation screw or valve for pump start Before filling the pump; pump installation location below the liquid level, the valve should be installed in the suction pipe and filter control device to prevent debris sucked into the pump, the filter area should be greater than 3-4 times the pipe area. 6, lift the pump at the outlet flow control valve on the outer pipe should also be installed check valve to prevent water hammer damage suddenly shut down. 7, must ensure that the pump installation height in line with the pump NPSH, and consider the pipeline loss and medium temperature. Second, IHF-lined fluorine plastic centrifugal pump operation 1. Pump before the pump should be filled with full plus liquid transport, no liquid start. 2. Close the outlet valve, turn on the power immediately after checking the steering pump must be consistent with the pump steering arrow, reverse operation is strictly prohibited, 3. After the pump reaches the normal speed of rotation, and then gradually open the outlet valve and adjust to the required work Conditions put into operation. In the discharge valve on the pipeline closed, the pump can not work continuously for more than 3 minutes. 4. Shutdown should be the first outlet of the valve closed, and then cut off the power. Third, IHF-lined fluorine plastic centrifugal pump maintenance 1. Regularly check the pump and motor, replace the vulnerable parts. 2. Always pay attention to the bearing box filled with high-quality calcium-based grease to protect the bearings under a good lubrication state. 3. Long-term downtime when not in use, in addition to the pump of corrosive liquid into the net, but should pay attention to the various components and pump flow channel clean, and cut off the power. 4. No-load pump is strictly prohibited. 5. If the media contains solid particles, the filter should be added at the pump inlet. Further Reading: pump valve pipe fittings Exhibition Water Expo Xiamen exhibition of marine equipment Internet + Forum Yiwu Fair 2016 exhibition mold top ten brands of the Internet information industry (Xiamen) Technology Co., Ltd. Author: Asian pumps Network Editor: Yao Xiaoxia (QQ / WeChat:) http://beng.liuti.cn/ (Service Hotline:)
Mosquito Killing Lamp
We supply various Mosquito Killing Lamp, including
mosquito killing bulb, mosquito killer machine.
The below information will help you to know
more about Solar Light.
Does mosquito killer lamp work?
Bug zappers work by emitting a UV light
that attracts bugs to the center of the device, where they're electrocuted,
usually between two metal grids. Because of the irresistible lure of their
light, bug zappers are incredibly effective at killing bugs.
Is mosquito lamp harmful to humans?
UV light from bug zappers will not harm you
or your family as they are not hazardous. That is why bug zappers are placed
high up in homes to catch more insects and present absolutely no harm to
humans.
Where do you place a mosquito lamp?
1. Place the Trap between the
mosquito source and areas of human activity.
2. Place the Trap as far away from
people (20-30 ft) and as close to the mosquito source as possible. (Attract
them to the Trap and not to you)
Do mosquito lamps work during the day?
Yes, the unit will continue to attract and
kill insects 24 hours a day.
If you want to know more about the products
in Mosquito Killing Lamp, please click the product details to view parameters,
models, pictures, prices and other information about Mosquito Killing Lamp, Mosquito
Killing Light, Light To Kill Mosquitoes,3 In 1 Mosquito Killing Lamp.
Whatever you are a group or individual, we
will do our best to provide you with accurate and comprehensive message about
Mosquito Killing Lamp!
Mosquito Killing Lamp,Mosquito Killing Light,Light To Kill Mosquitoes,3 In 1 Mosquito Killing Lamp
NINGBO LONGFLIGHT INTELLIGENT TECHNOLOGY CO.,LTD , https://www.long-flight.com