2. Use an easy assembly relationship to determine complex assembly relationships for poor operation.
See the front left door assembly drawing. In the past, the B-door hinge and the door panel were very difficult to assemble. Sometimes the sweat was not overwhelming, because a small piece affecting the progress of the whole project is a matter of getting angry. Later, I found that inserting in the assembly constraint command is the most convenient. Why not put the B-door hinge on the door shaft on the unit cabinet frame, and then upgrade it to the front left door assembly. Later, I found this. The method is really amazing.
3. Use the intuitive method to determine the size of the part.
It is not easy to determine the length of the lock lever in the lock bar design by measurement and calculation. So I thought that since Invento is a 3D software, it is very straightforward. Why do you have to calculate it? So hide the other parts and reveal all the lock bars to be determined. By changing the sketch of each lock bar, it is repeated several times until the lock head is up. The best position for the door top piece. Why not save time and effort?
4. Pay attention to correcting the mistakes of Invento in time.
In the past, it was found that there were often cases of error reporting, sometimes assembly constraints or assembly constraints, and sometimes reference relationships. At this time, it is often the second monk who can't touch the head and can only accept it. When an assembly is finished, you can see the yellow warning in the component panel. It is not a taste for me who is pursuing perfection. So I decided to remove this roadblock. After careful research, it was found that an error would cause the following work to be impossible, because some orders were not learned. In the front left door assembly drawing, the trip switch top contact member and the front left door panel are assembled with a fault. In this assembly relationship, add the fitting in the assembly constraint dialog once, and the surface is flush twice to properly assemble the stroke switch top contact. This kind of mistake is caused by the fact that the command is not thoroughly understood and leads to over-constraints. Invento will stop you from going down until you pass the order and it will let go. A misalignment is likely to be an accident in the positional relationship between the two parts. At this time, Invento reports an error, but you have to accept it, but there is a possibility of error. It should be an error to correct the mistake. In this sense, Invento has powerful immune functions.
5, grasp the reference relationship to stay the best time.
It is very scientific to establish new parts using projection geometry in assembly. References between parts and assemblies or between parts and parts sometimes give you convenience and sometimes cause trouble. In the early design, the parts were not completely shaped, and there is a reference relationship. If the corresponding part of a part is changed or the associated assembly is automatically changed. Once the part is confirmed, the reference relationship is best deleted. As mentioned above, it will be reported because of moving a part Invento, so you will be upset.
6, the array components must grasp the timing.
It is the best thing for an array of the same multiple parts with certain regularities. But before using this command, you must first grasp the timing. After assembling the middle and lower units in the unit assembly drawing, it is easy to generate the unit on the upper layer of the array, but you must grasp the timing of the machine. Once the array is first degraded and then the unit is downgraded to the next component, then the array elements in the new component do not exist and do nothing. So be sure to wait until the parts are arranged before you enjoy the array. Only when you have a good time can Invento take advantage of it.
7. Measuring the distance between two holes in Invento is harder than going to the sky, but that is the feeling of the first time.
When measuring, just select the surface where one of the holes is located, and then click the two holes to be measured. It is found to be so simple.
8. When using the projected geometry element method when editing a part, sometimes the contour of the part related to it is not visible. In this case, you need to select the line frame display to find it.
9. In engineering drawings, dimensioning sometimes does not require specific values. For example, "L" is the selected size before, press the right button to select the text before the <<>> plus "L" but finally "L=<<>>". I started to confuse at the beginning of this question, and then inadvertently I chose only a "L" after selecting the hidden value in the right-click drop-down menu.
In short, Invento is a perfect software. Sometimes some small tricks and small methods may be introduced to you in detail in the textbooks, but for those design engineers who are life-times, it may be a shortcut to learn software. If it is not on the textbook, it is also a supplement to Invento. The above is a little bit of experience and experience in my use, I hope to bring you some help.
Previous page
Grey Color Self Adhesive Car Roll Film
Grey Color Self Adhesive Car Roll Film,Gray Color Privacy Film,Car Tinting Film,Outdoor Smart Car Film
Shenzhen YuGuang New Material Co.,Ltd , https://www.ygsmartfilm.com