Network cable wall socket installation method network cable wall socket how to buy

Now is the Internet age, so it is said that almost every family will install a network. Through the network, we can understand a lot of things. Now, no matter what is going to be communicated through the network, the network cable in the home is the need to install the socket, then the network cable wall socket What are the installation methods? How to choose the cable wall socket? The following is a small series of decoration home network to introduce to you.


网线墙壁插座


First, the network cable wall socket installation method


1. Draw the twisted pair from the cassette, reserve a 40 cm line, and cut off the excess line. Use a stripping tool or a crimping tool to strip the outer sheath of the twisted pair about 10 cm in length. Separate the twisted pair cores by line pair, but do not disassemble the pairs first. Only remove the corresponding pairs before pushing them into the string. Select our preferred line-sequence mode according to the color code indicated on the information module (Note: Only one line-sequence mode is used uniformly in one wiring system, otherwise it will be difficult to check if the network is unreasonable), and the skin will be stripped. The rear end faces of the module are parallel, and the two hands are slightly twisted to open the twisted pair, and the wire is pressed into the corresponding wire slot with a little force.


2. After all the pairs are pressed into the slots, the 110 core tools can be used to further press one core into the slot. The use of the 110 wire tool is as follows: the cutting edge of the cutting wire is always toward the side of the module. The wire-punching tool and the module are inserted vertically into the slot, and the force is impacted vertically, and a “click” is heard, indicating that the groove of the tool has been The wire core is pressed into place and has been inserted into the metal clip, and the metal clip has been cut into the edge of the skin to form a copper wire core to form a passage. Here, pay attention to the following two points: the knife edge is outward--if you forget to become inward, the press-in also cuts off the copper wire that should be connected; the vertical insertion--slanting will make the metal clip's mouth support Open, no more ability to bite, and the string will also collapse, difficult to repair, this module can be scrapped. If the newly purchased good tool is in the impact, it should be able to cut off many cores. If not, I will strike several times and can be screwed off by hand.


网线墙壁插座


Second, how to choose the network cable wall socket


1. Look at the internal material. Usually, the copper inside the switch is made of copper; the copper inside the socket is made of phosphor bronze for one-time die-casting, which has good conductivity and heat dissipation. Phosphorus copper is the strongest one, which is high in strength, good in electrical conductivity, and not easily deformed. The switch contacts are made of silver alloy contacts, which prevent arcing caused by oxidation during opening and closing, and have good electrical conductivity. In addition, the wiring method is saddle wiring, the terminal screws are plated, the contact surface is large and good, the pressure line capability is strong, and the wiring is stable and reliable.


2. See if there is a protective door. The safety protection door of the socket is indispensable. When selecting the socket, try to choose the product with the protection door. Look at the socket clips. Also, check the tightness of the socket clips. The smooth insertion force is a key factor, and the strong extrusion makes the plug not easy to fall off, which can effectively reduce the occurrence of power failure accidents caused by non-human factors. The socket clip is made of phosphor bronze. Because of its good electrical conductivity and strong fatigue resistance, the number of plugging and unplugging is up to 8000 times (the national standard is 5000 times).


3. Look at the structure and appearance, usually the product shell is shiny: the panel of the switch socket should be made of plastic, the material is even, and the surface is smooth and textured. The panel materials are made of native PC material (anti-ballistic rubber), which is excellent in flame retardancy, insulation and impact resistance. And the material is stable and not easy to change color. The use of switch sockets made of such materials can greatly reduce the occurrence of fires and the like due to circuit causes.


Now the family will install the network cable, there will be socket installation in the place where the network cable is installed, generally the wall socket is installed, then the installation method of the cable wall socket and how to buy it, everyone who wants to know this knowledge through Xiaobian The introduction also understands, then if you still want to know more about decoration information, please continue to pay attention to the decoration home Internet cafe.


Bring cozy and warm texture to your space with our Macrame Wall Hangings . Clever design so that it makes a stylish impact , it adds a mellow bohemian feel to your room . This macrame wall hanging is perfect for giving your home decor that natural , and will add a personal unique touch to any space .

Macrame Wall Hangings

Wall Macrame,Macrame Wall Hangings,Macrame Wall Decor,Large Macrame Wall Hanging

Shandong Guyi Crafts Co.,Ltd , https://www.guyicrafts.com

This entry was posted in on