Sometimes, when we use a Reitz blower, it may not require a large amount of air to achieve good results, only by controlling the excess volume in order to save costs, no matter what type of fan air volume control problem sometimes, when we use the Reitz blower may not Need a large amount of air can achieve good results, only by controlling the excess volume in order to save costs, no matter what type of fan air volume control problem, Dongguan Ruitian Electromechanical "target=_blank> Electromechanical Technology Co., Ltd. today with Reitz Centrifugal For example, the fan introduces the user how the air of the Reitz centrifugal fan is controlled.
The user working process of the outer rotor fan made the first understanding, in order to have the basic grasp of the fan, the slave in the fluid mechanical gas pressure side by side air. The centrifugal fan can be output with two types of right-handed and left-handed, and mechanical energy. From the fault on the motor side, the impeller rotates clockwise, called the right-hand rotating fan, which is counter-clockwise twisted and is called the left hand. The task can be basically the same as the turbine, except that due to the low gas flow rate and pressure changes, the individual does not need to consider the volume change of the gas, ie the gas does not shorten the fluid treatment.
After the new installation begins to officially run the fan, there is too much or too little or during operation, one of the following ways can be used: speed control flow changes from the fan. The degree to which the control flow is turned on and off controls the door. The network controls the resistance coefficient of the flow change. Replace the fan control flow with a higher or lower pressure. Using these methods can help the user to control the fan air flow very well, but such control is more complicated, the user can also limit the process is installed in the fan. Considering the main factor of the control air volume of the Reitz fan impeller is solved, the quality also affects the air is Very large, so be sure to check the integrity of the fan impeller before installation. It must be ensured that each component of the Reitz fan is effective, does not damage any quality phenomenon, and fundamentally grasps the fan to make the fan better adjust the air. flow.
By these methods, it is better to control the air flow of the fan, but the user to improve the use of the fan is only insufficient efficiency from the air control, and important factors for other fans need to be considered, such as the solution efficiency of the Reitz fan failure, the pump The noise solution is an important factor affecting the efficiency of the Leitz fan.
Http://news.chinawj.com.cn
Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
CNC Internal Cylindrical Grinding is mainly used for grinding the inner hole and end face of pot teeth and large bearing ring parts to ensure the accuracy of the inner hole and end face. Is a new generation of high-precision, high-efficiency production machine tools. The entire grinding cycle of the machine tool is automatically completed, and the operator only needs to assemble and disassemble the workpiece. CNC internal grinder is used to grind cylindrical and conical small holes, and can also grind outer circle and end face. The working spindle, Internal Grinding head and external grinding head are all lubricated with oil mist. The CNC internal grinder system has strong programming functions, simple operation and easy to learn, and has a variety of special functions that meet the requirements of grinding processing, which can meet the processing needs of users for a variety of parts.
Grinding aperture
Ñ„1 ~ 450mm
Grinding depth
200mm
Workpiece maximum rotation straight and light
1050mm
Maximum grinding width of inner grinding head
30mm
Maximum grinding end width of end grinding head
180mm
Internal feed beam transverse feed stroke (X axis)
400mm
Longitudinal feed stroke of internal grinding frame (Z axis)
350mm
End grinding beam horizontal reciprocating stroke (W axis)
400mm
Longitudinal reciprocating stroke of end grinding frame (U axis)
350mm
Maximum speed of feed axis
8m / min
Feed axis resolution
0.0005mm
Workpiece spindle speed
30 ~ 100r / min
Machine power
22KW
Machine weight
Internal Cylindrical Grinding
Cylinder Tube,Internal Cylindrical Grinding,Internal Grinding Cylinder Tube,Cylinder Tube After Internal Grinding
Dayue Precision Technology (Dongguan) Co., Ltd. , https://www.dayuechn.com