Italian quartz stone countertops    Vantage Kitchen Cabinets
First, after the table is installed, it must be level. This is very simple, a level rule to get it. There are certain problems with the leveling of the tabletop. In the final analysis, this is related to the fact that there is a relationship between the cabinet and the university. The cabinets are uneven and how the tabletops are flat? There is the same time when installing, over time, it is said that after the Kangjie cabinet is installed, someone will check the leg of the cabinet. If it is easy to screw, the installation worker should be fine, because the long-term stress will not be uniform. Causes the cabinet to tilt.
Second, meet. One of the advantages of artificial stone is that there is no splicing. If you can clearly see the glue line, you will certainly not be able to meet every time, and you will not have to worry about how many reasons the installer has said. I had previously encountered a complaint. The countertops were all glue lines. I was terribly apprehensive. When the owners accepted the installation, I questioned the owners. How could such a countertop be installed? The owner’s reply made me speechless. “The installation worker said: This is the case with XX artificial stone. Who told you to make XX artificial stone countertops?â€
Third, the color difference. There are chromatic aberrations in different batches of artificial stone, but the installed countertops cannot have chromatic aberration, and the problem cannot be made by consumers.
Fourth, man-made stone countertops, liners essential. Some use strip linings, some use integral linings, and others use a structural frame. However, the protection of the countertops is necessary.
Fifth, open hole. The opening should be smooth, not serrated, and the four corners must be curved, but not simply rectangular. Moreover, the four corners should be reinforced. For example, if the hole is in the basin or the stove is empty, the force in this place is Bigger, unsatisfactory, and problematic. The heat insulation treatment of the burner hole is indispensable.
Six, after the water. After the stall is a very complicated place, to make a perfect after-water, there must be two stitching, but I also found that some manufacturers came up with a "good" approach, directly stick up the slats, the thing is Save a lot, clean up the dead corner and left it, the integration of artificial stone countertops, easy to take care of the advantages have also been saved.
Seventh, retreat, if the table is longer, especially on both sides of the top wall, expansion joints are indispensable, otherwise, the destructive power of hot rising and shrinking is still very large.
Second: Man-made stone countertops processing and installation of attention!
First, when installing the countertops, first check the cabinets to ensure that the cabinets are horizontal. After the countertops are installed, check the levelness of the countertops so that the countertops will not be deformed or cracked due to the unevenness of the countertops.
Second, gas burner hole (basin hole) of the four corners for the diameter of not less than 20mm arc-shaped rounded corners, and use sandpaper wipe smooth, can not have a sawtooth shape, this is to avoid stress points in the hole, the force in the table Uneven cracking; four corners of the gas burner opening are reinforced along the edge of the burner hole by the curved plate block, because the gas stove has a certain weight, and the pot should be put on the top, and only 12.7 mm thick man-made The pressure that the stone can withstand is limited, so do reinforcement treatment to avoid deformation or cracking of the table when the pressure is too great. In the same way, the stainless steel basin must be reinforced on all four sides. Other openings must also be reinforced.
Third, the edge of the stove with insulation cotton and wrapped with aluminum foil for heat insulation treatment, so as not to overheat the cooking stove when cooking, so that the table top part of the thermal expansion of the stove hole cracking.
Fourth, under the table to have a backing plate to support the table, pad with three 100 mm wide, thick 15 mm above the particle board or MDF can be fixed with plastic glass in front of the back of the table. Star pots and stoves add vertical plate. All damper boards should be made of damp-proof plates so as to prevent the dampers from damaging the tabletop.
Fifth, in the need for splicing, the mouth should be wiped clean with alcohol or water, so as to avoid too much dust at the seams, affecting the bonding effect, resulting in cracking joints.
6. The 3-5mm expansion joints should be left on the top of the table top, and the table top should be more than 3 meters. The expansion joints should not be less than 5mm.
7. The table top must be carefully polished and polished. The problem to be noted when sanding is: After replacing the sandpaper, you must polish all traces of the previous sandpaper, and then replace the higher-numbered sandpaper until The gloss of the artificial stone is polished out.
Kitchen Decoration Construction Acceptance Plate Glass America Stainless Vantage Counter Cabinet Door Glass Counter Stainless Steel Cabinet Stainless Steel Whole Cabinet Glass Door
7+Person Hot Tub
7+ Person Hot Tub,large outdoor spa,outdoor living pool spa,spa with outdoor heated pool,modern outdoor hot tub
Guangzhou Aijingsi Sanitary Products Co.,Ltd , https://www.comoxvalleyhottubs.com