How to deflate geothermal? How should geothermal gas release? Floor heating is recognized as the most comfortable home heating method, but there are also many consumers who say that the warmth of the home will not be hot. It is very inconvenient. According to Xiaobian, indoor temperature is not hot because there is accumulation in the geothermal pipe. Your helium and gas affect the water cycle. Just put your home's geothermal heat pipe down. Then how should the gas be deflated? In response to the demands of consumers, Xiao Bian will tell you today how to properly heat up the ground. Let go and hope to help everyone.
First, before releasing gas to the ground, prepare a new water pipe, pliers, or wrench, etc., and then find the location of the water discharge. In general, the upper water inlet pipe has a gas outlet, and the lower water outlet pipe also has a gas outlet. If some consumers are not sure, they can also touch it by hand. The heat is the inlet pipe, and the cool water pipe is the return pipe. It is generally the gas that is put into the water pipe first. First of all, we must first connect the water pipe to the bleed valve of the water inlet pipe of the water separator. At the same time, we must remember that it is best to take care of it when it is deflated, because the deflation hose may pulsate, so we must pay attention to it. . Then use pliers to gently open the valve and wrap it around the valve with a towel. This is done because there will be water overflowing from the valve during deflation, which will prevent the water from flowing around.
Second, what we need to do is to put the gas back into the water pipe. At this time, the main valve of the backwater main, which is the green or red long handle, must be closed first, and normally it turns off at 90 degrees. The process of deflation of the return pipe is the same as that of the inlet pipe, except that it is necessary to connect the pipe to the bleed valve of the water return of the water separator. Then everyone can put a single water pipe in each room one by one. As we all know, the water separator is connected to a single geothermal pipe, and each geothermal pipe has a small inlet valve and a small return valve control. . The specific operation is to close the main return valve, and close the small inlet and outlet valves of each geothermal pipe. Then the small inlet and outlet valve of the first geothermal pipe is opened from the head of the manifold. The bleed valve of the water pipe vents until warm water is released.
Third, there are many consumers who ask what kind of situation the Xiaobian is considered to be successful in deflation. Xiaobian tells everyone here that the main reason is to put geothermal pipes in which there is no sewage and gas spouting, and the basic steady state will be achieved. . After the deflation is successful, everyone will open all the water-passing valves, including the main water return pipe and each single pipe mentioned above, and then close the air-releasing valve.
How do you deflate geothermal? I believe that after reading the above explanations by Xiaobian, you already have a basic understanding of the steps. I hope you can help consumers who have this need. Here, Xiao Bian also reminds everyone that if there is a problem of discharge during the deflation, it is necessary to immediately close the main valve of the main inlet pipe and the main return pipe, and then take Other measures.
First, before releasing gas to the ground, prepare a new water pipe, pliers, or wrench, etc., and then find the location of the water discharge. In general, the upper water inlet pipe has a gas outlet, and the lower water outlet pipe also has a gas outlet. If some consumers are not sure, they can also touch it by hand. The heat is the inlet pipe, and the cool water pipe is the return pipe. It is generally the gas that is put into the water pipe first. First of all, we must first connect the water pipe to the bleed valve of the water inlet pipe of the water separator. At the same time, we must remember that it is best to take care of it when it is deflated, because the deflation hose may pulsate, so we must pay attention to it. . Then use pliers to gently open the valve and wrap it around the valve with a towel. This is done because there will be water overflowing from the valve during deflation, which will prevent the water from flowing around.
Second, what we need to do is to put the gas back into the water pipe. At this time, the main valve of the backwater main, which is the green or red long handle, must be closed first, and normally it turns off at 90 degrees. The process of deflation of the return pipe is the same as that of the inlet pipe, except that it is necessary to connect the pipe to the bleed valve of the water return of the water separator. Then everyone can put a single water pipe in each room one by one. As we all know, the water separator is connected to a single geothermal pipe, and each geothermal pipe has a small inlet valve and a small return valve control. . The specific operation is to close the main return valve, and close the small inlet and outlet valves of each geothermal pipe. Then the small inlet and outlet valve of the first geothermal pipe is opened from the head of the manifold. The bleed valve of the water pipe vents until warm water is released.
Third, there are many consumers who ask what kind of situation the Xiaobian is considered to be successful in deflation. Xiaobian tells everyone here that the main reason is to put geothermal pipes in which there is no sewage and gas spouting, and the basic steady state will be achieved. . After the deflation is successful, everyone will open all the water-passing valves, including the main water return pipe and each single pipe mentioned above, and then close the air-releasing valve.
How do you deflate geothermal? I believe that after reading the above explanations by Xiaobian, you already have a basic understanding of the steps. I hope you can help consumers who have this need. Here, Xiao Bian also reminds everyone that if there is a problem of discharge during the deflation, it is necessary to immediately close the main valve of the main inlet pipe and the main return pipe, and then take Other measures.
How to install electric heating with a loft How to avoid the decoration contract pitfalls
We are high quality single handle Kitchen Faucet suppliers, the biggest advantage of the single handle kitchen faucet is that it is more convenient to clean the corners of the kitchen interior, as well as places that cannot be reached by ordinary faucets, expanding the cleaning area and bringing convenience to kitchen cleaning.We also have good quality Pull down kitchen faucet and high quality basin faucet.
Single Handle Kitchen Faucet,Hot Sale Single Handle Kitchen Faucet,Good Quality Single Handle Kitchen Faucet
kaiping aida sanitary ware technology co.,ltd , https://www.kpaidafaucets.com